产品描述 | 日本丰和三爪中实卡盘H01MA
Series number
| | Specifications |
|
|
4
| 5
| 6
| 8
| 10
| 12
|
Jaw movement (Dia.) (mm)
| 5
| 7
| 8.8
|
| Plung stroke (Cylinder stroke) (mm) | 15
| 20
| 25
|
Recommendd outside chucking
diameter for standard soft blank jaws | Max.
| 110
| 135
| 165
| 210
| 254
| 304
|
Min.
| 6
| 15
| 20
| 18
| 24
| 10
|
| Max. speed (r/min.) | 5,000
| 4,500
| 4,000
| 3,500
| 2,800
|
| Max. Input force (kN) | 4.4
| 6.4
| 14.7
| 24.5
| 30.4
| 39.2
|
Clamping force at Max. input force
(Total jaw force) (kN) | 12.1
| 17.7
| 41.2
| 67.7
| 94.1
| 124
|
| Moment of inertia J (kgm2) | Note 1 |
| 0.005
| 0.015
| 0.040
| 0.11
| 0.26
| 0.66
|
| Weight with standard soft blank jaws (kg) | 4
| 6
| 12.5
| 23.3
| 33.5
| 57.2
|
| Matching cylinder | Max. pressure to
operate chuck (MPa) |
| HH4C | 80/1.0
| 80/1.5
| “
100/2.1
| “
125/2.2
| “
125/2.6
| “
140/2.7
|
| HO5CH | 100/0.6
| 150/0.4
| 175/0.6
| “
250/0.5
| “
300/0.4
| “
300/0.6
|
|
|
|
|
4
| 5
| 6
| 8
| 10
| 12
|
| A | 110
| 135
| 165
| 210
| 254
| 304
|
| B2 | Min. | 27
| 30
| 40
| 44
| 50
| 58
|
| C | H7 | 60
| 80
| 90
| 120
| 140
|
| D | 6
| 7
| 7.5
|
| E | 52
| 72
| 85
| 95
| 115
|
| F | 80
| 100
| 130
| 150
| 170
|
| G | 3- M8X1.25
| 3- M16X2
| 6- M16X2
|
| H | 16.5
| 20
| 22
|
| J | M10X1.5
| M12X1.75
| M16X2
| M20X2.5
| M24X3
|
| K | 25
| 36
| 46
|
| L | Max. | 5
| 9
| 89.5
| 105
| 114
| 127
|
| Min. | -10
| -6
| 74.5
| 85
| 89
| 102
|
| M | . | -
| 23
| 28
| 34
| 39
|
| Max. | -
| 25
| 28
| 36
| 40
|
| N | Max. | 26
| 32
| 41.8
| 42.3 | 48.5
| 52
|
| Min. | 23.5
| 29.5
| 38.3
| 38.8 | 44.1
| 47.6
|
| O | Max. | 10
| 11.5
| 13
| 27
| 37.5
| 55
|
| Min. | 7
| 12
| 13.5
| 16
|
| P | 3
| 5
|
| R | -
| 15
|
| W | 25
| 28
| 32
| 38
| 44
| 52
|
| X | 27
| 43
| 53
|
| J1 | 25
| 31
| 34
| 40
| 50
|
| Note: HO1MA6 and 8 are also available with serration pitch 1.5mm. |
| .Note: |
- The four times of this value is equivalent to GD2.
If the plunger stroke of a chuck is shorter than that of a cylinder, the latter must be adjusted to the former. The cylinders of model marked “ are required limiting of stroke. When the Max. speed of a rotating cylinder is lower than that of a chuck, observe that of a rotating cylinder. | 
| .Note: |
- The four times of this value is equivalent to GD2.
If the plunger stroke of a chuck is shorter than that of a cylinder, the latter must be adjusted to the former. The cylinders of model marked “ are required limiting of stroke. When the Max. speed of a rotating cylinder is lower than that of a chuck, observe that of a rotating cylinder. |
